What to Check Before Taking Delivery of a Skid Steer Loader
A pre-delivery inspection saves time and trouble later
Skid steer loaders are rugged machines built for tight spaces and heavy work. Whether you are adding one to a fleet or buying your first unit, the moment of delivery is the best time to catch small problems before they become expensive repairs. A thorough inspection before you sign off protects your investment and keeps the job moving. Here is what to look at, and why each point matters.
Start with the basics: paperwork and visual condition
Before you climb onto the machine, check the serial number against the bill of sale or lease agreement. Mismatched numbers are rare but can cause title headaches later. Walk around the entire loader in good light. Look for fresh dents, cracked welds, or paint that does not match the rest of the unit. A scuff here or there is normal for a used machine, but deep gouges or bent frame members suggest a hard previous life. Also confirm that all decals and warning labels are present and legible. Missing safety labels are a red flag that maintenance may have been skipped.
Open the engine compartment and look for oil or hydraulic fluid weeping from gaskets, hoses, or fittings. A little dust stuck to oil is not a crisis, but active dripping means a seal or hose needs attention. Check the coolant level and colour. Clean coolant is a sign the engine was not overheated. Muddy or rusty coolant suggests neglect. If the machine has a battery, inspect the terminals for corrosion and make sure the battery is secured in its tray.
Hydraulic system: the heart of the loader
Skid steer loaders depend on hydraulic power for lifting, tilting, and steering. Check the hydraulic fluid level in the reservoir while the machine is cold. Low fluid can indicate a leak or a system that was not topped off. Look at the colour of the fluid on the dipstick or sight glass. Clean hydraulic fluid is a clear amber. Dark or milky fluid points to contamination from heat or water, which can damage pumps and valves.

With the engine off, operate each control lever slowly. The handles should move smoothly without binding. Then start the engine and let it warm up to operating temperature. Cycle the lift arm and bucket through their full range of motion. Watch for jerky movement, drifting, or slow response. Any hesitation in the hydraulic circuit often means air in the lines, a worn pump, or a failing control valve. Listen for unusual sounds from the pump, especially whining or knocking. A quiet, steady hum is normal; anything else calls for a closer look by a mechanic.
Undercarriage and tracks or wheels
The undercarriage takes the worst abuse. If the loader has tracks, inspect the track tension and look for missing or damaged pads, links, or sprocket teeth. Uneven wear on the track chain or sprocket indicates misalignment or a worn idler. For wheeled models, check tyre tread depth and look for sidewall cuts, bulges, or uneven wear patterns. Also check the inflation pressure when the machine is cold. A tyre that is low on air may have a slow leak or a damaged bead.
Ground clearance is worth a quick measurement if you plan to work on rough terrain. A loader with sagged suspension or worn bushings will sit lower than spec, making it easier to high-centre on rocks or stumps. Look at the axle housings and final drives for leaks. A small amount of seepage around a seal is common on older machines, but a steady drip means the seal needs replacing soon.
Bucket, attachment, and lifting system
Inspect the bucket or attachment for cracks, bent cutting edges, and worn bolt holes. A damaged bucket reduces digging efficiency and can break during heavy use. Check the quick-attach plate or pin system that holds the attachment to the loader arms. Worn pins or bushings create slack that makes the bucket wobble, which wears out the linkage faster. Lift capacity depends on the condition of these connection points as much as on the hydraulic cylinders. If the attachment does not seat flush, do not force it; the machine may need a different adapter or replacement bushings.
Operate the lift circuit with the bucket empty, then with a light load if possible. The arm should rise and lower smoothly without sagging when held in position. If the bucket drifts down over a few seconds, the hydraulic cylinder seals are bypassing fluid. That is a repair you want the seller to handle before delivery.
Operator controls and safety systems
Sit in the operator station and check that the seat belt or restraint system is intact and that the lap bar or rollover protection structure is sound. Test every pedal, lever, and switch. The steering controls should return to neutral when released. Confirm that the parking brake holds the machine on a slight slope. If the loader has a quick-disconnect coupling for auxiliary hydraulics, verify that the coupler is clean and that the dust cap is in place.

Check the gauges on the dashboard. The hour meter should match the seller's stated hours. A mismatch does not automatically mean tampering, but it deserves an explanation. The temperature gauge should rise steadily during warm up. The hydraulic pressure gauge, if fitted, should show pressure within the normal range when the lift circuit is activated. Low pressure means the relief valve or pump may need service.
Traction is easy to overlook at delivery, but it determines how the loader performs in mud, snow, or loose soil. Look at the tread pattern on tyres or the grouser condition on tracks. Worn traction surfaces mean the machine will spin more easily, wasting fuel and time. If the seller offers a test area, drive the loader in a straight line and then turn sharply. Listen for clunks from the final drives and feel for vibration through the steering levers.
If the loader has additional attachments such as a grapple, auger, or pallet fork, test the attachment's own hydraulic circuit if it has one. Check that the hoses and fittings are compatible with the loader's auxiliary hydraulics. Mismatched couplers are a common frustration that can delay work on the first day.
A well-prepared delivery inspection takes about an hour. That hour can save days of downtime later. For buyers who want to compare specifications across models or who need help locating a specific machine, online resources such as epowerhousellc.com offer listings and product details for a wide range of industrial equipment including skid steer loaders. It is a practical starting point when you are researching options or verifying that the machine you are inspecting meets the published specs.
After the inspection, write down your findings. If the machine passes every check, you can accept delivery with confidence. If you spot issues, you have a clear list to discuss with the seller before finalising the transaction. A loader that arrives with a clean bill of health will start working for you from day one, and that is the whole point of the purchase.
Remember that the inspection is not a substitute for professional maintenance. Even a machine that looks perfect on delivery will need regular fluid changes, filter replacements, and scheduled service. But catching problems at the start means you begin with a known baseline, and that makes every future service interval easier to track.

For anyone who sells or rents heavy equipment, a consistent inspection process also builds trust with customers. When a machine leaves the yard with verified hydraulic flow, correct ground clearance, and a sound attachment, the next operator can focus on the job instead of worrying about breakdowns. That is why many dealers and rental houses follow a standard checklist before every delivery. Buyers are wise to do the same.
Taking a few extra minutes at delivery to inspect a skid steer loader pays off in reliability, safety, and peace of mind. Whether you are a contractor, a municipal crew, or a rental customer, the same principle applies: know what you are getting before you put it to work. And if you are still shopping, resources like epowerhousellc.com can help you compare specs across makes and models so you arrive at delivery already informed.